09:31 <loki666> Mis012[m]> looks like I bricked a SM6115 now... Would you know the hash segment version the board expect for the ABL ?

09:32 <loki666> Tried V3... No dice

09:32 <Mis012[m]> is it sb off?

09:32 <loki666> Yes

09:33 <loki666> Currently it even don't show up on my USB... Hopefully the battery will drain, in a week or two

09:33 <loki666> ... Eventually

09:33 <Mis012[m]> uhm...

09:33 <Mis012[m]> you can reset it by holding the power button

09:34 <Mis012[m]> on older stuff also needed to hold vol down (resin) but probably not 6115

09:34 <loki666> Yes I tried, but not much on USB... I'll try again with a shorter watch delay

09:35 <Mis012[m]> well, you may need to use the strap

09:35 <loki666> The strap ?

09:35 <Mis012[m]> the one for boot from usb

09:36 <Mis012[m]> that is usually routed to a testpoint somewhere with 1v8 next to it

09:36 <loki666> Ah yes to force EDL... I'll try the EDL USB cable before resorting to that

09:39 <Mis012[m]> loki666: I think v3 is correct

09:39 <Mis012[m]> what were you trying to do?

09:40 <loki666> Same as with the SM8650... Have an ABL that allows to boot an EPS partition

09:41 <loki666> Maybe abl2esp doesn't work on SM6115... Missing EFI protocol maybe

09:41 <Mis012[m]> on 6115 you should be able to put u-boot instead of XBL

09:43 <loki666> But on the SM6115 I don't even have the panel setup, so if abl2esp fails, I don't know

09:43 <Mis012[m]> can try to debug it with EUD

09:43 <loki666> EUD ?

09:44 <Mis012[m]> https://github.com/linux-msm/openocd has some basic info

09:46 <loki666> Ok but I first need to bring it back alive... I'll try the EDL cable or strap

09:46 <loki666> Thanks

09:50 <Mis012[m]> strap should always work, but need to disassemble the device

09:50 <Mis012[m]> don't recall where cable is handled

10:11 <loki666> Yeah.. in any case strap / EDL cable only works from a cold boot, I understand, so I'll need to unplug the battery anyway

10:12 <loki666> The board seems pretty cold... So I guess it will take time for the battery to drain out...

10:25 <Mis012[m]> holding power button for like 30 sec is also cold boot

10:51 <loki666> Mis012[m]: doesn't seems to work either, holding 30 sec, with various method to go in EDL... but the guy is a no show

10:51 <Mis012[m]> maybe it's more than 30sec, probably not more than a minute though

10:51 <Mis012[m]> that + strap should work

10:52 <Mis012[m]> also may need to hold vol down but I doubt it

10:52 <loki666> well, If I need to reach strap, I'll just unplug the battery

10:52 <loki666> tried vol+, vol- and vol+ with vol-

10:52 <loki666> and EDL

10:58 <loki666> does holding power for 30s, shut it down, or reset as a cold boot ?

11:00 <Mis012[m]> reset

11:01 <Mis012[m]> it literally makes the pmic cut off power to the SoC, but it does start it back up

11:02 <loki666> well, I guess I'm good for the strap then